우리 ITExamDump에서는 최고이자 최신의Cisco 인증642-188덤프자료를 제공 함으로 여러분을 도와Cisco 인증642-188인증자격증을 쉽게 취득할 수 있게 해드립니다.만약 아직도Cisco 인증642-188시험패스를 위하여 고군분투하고 있다면 바로 우리 ITExamDump를 선택함으로 여러분의 고민을 날려버릴수 있습니다.
많은 분들이 고난의도인 IT관련인증시험을 응시하고 싶어 하는데 이런 시험은 많은 전문적인 IT관련지식이 필요합니다. 시험은 당연히 완전히 전문적인 IT관련지식을 터득하자만이 패스할 가능성이 높습니다. 하지만 지금은 많은 방법들로 여러분의 부족한 면을 보충해드릴 수 있으며 또 힘든 IT시험도 패스하실 수 있습니다. 혹은 여러분은 전문적인 IT관련지식을 터득하자들보다 더 간단히 더 빨리 시험을 패스하실 수 있습니다.
Cisco 642-188 시험을 어떻게 통과할수 있을가 고민중이신 분들은ITExamDump를 선택해 주세요. ITExamDump는 많은 분들이 IT인증시험을 응시하여 성공하도록 도와주는 사이트입니다. 최고급 품질의Cisco 642-188시험대비 덤프는Cisco 642-188시험을 간단하게 패스하도록 힘이 되어드립니다. ITExamDump 의 덤프는 모두 엘리트한 전문가들이 만들어낸 만큼 시험문제의 적중률은 아주 높습니다.
시험 번호/코드: 642-188
시험 이름: Cisco (ITI Implementing Cisco TelePresence Installations)
당신이 구입하기 전에 시도
일년동안 무료 업데이트
100% 환불보장약속
100% 합격율 보장
Q&A: 140 문항
업데이트: 2014-02-12
Cisco인증 642-188시험을 패스하기 위하여 잠을 설쳐가며 시험준비 공부를 하고 계신 분들은 이 글을 보는 즉시 공부방법이 틀렸구나 하는 생각이 들것입니다. ITExamDump의Cisco인증 642-188덤프는 실제시험을 대비하여 제작한 최신버전 공부자료로서 문항수도 적합하여 불필요한 공부는 하지 않으셔도 되게끔 만들어져 있습니다.가격도 착하고 시험패스율 높은ITExamDump의Cisco인증 642-188덤프를 애용해보세요. 놀라운 기적을 안겨드릴것입니다.
Cisco 642-188인증은 아주 중요한 인증시험중의 하나입니다. ITExamDump의 베터랑의 전문가들이 오랜 풍부한 경험과 IT지식으로 만들어낸 IT관연인증시험 자격증자료들입니다. 이런 자료들은 여러분이Cisco인증시험중의642-188시험을 안전하게 패스하도록 도와줍니다. ITExamDump에서 제공하는 덤프들은 모두 100%통과 율을 보장하며 그리고 일년무료 업뎃을 제공합니다
IT인증자격증을 취득하려고 마음먹었으면 끝까지 도전해봐야 합니다. Cisco인증 642-188시험이 아무리 어려워도ITExamDump의Cisco인증 642-188덤프가 동반해주면 시험이 쉬워지는 법은 많이 알려져 있습니다. ITExamDump의Cisco인증 642-188덤프는 100% 패스보장 가능한 덤프자료입니다.한번만 믿어주시고ITExamDump제품으로 가면 시험패스는 식은 죽 먹기처럼 간단합니다.
ITExamDump에서 Cisco인증 642-188덤프를 구입하시면 퍼펙트한 구매후 서비스를 제공해드립니다. Cisco인증 642-188덤프가 업데이트되면 업데이트된 최신버전을 무료로 서비스로 드립니다. 시험에서 불합격성적표를 받으시면 덤프구매시 지불한 덤프비용은 환불해드립니다.
642-188 덤프무료샘플다운로드하기: http://www.itexamdump.com/642-188.html
NO.1 The Cisco TelePresence System 1100 and Cisco TelePresence System 1300 mounting brackets has
limited side-to-side adjustability. What is the first thing to consider before you mount the bracket?
A. Attach the sliders on the bracket to the wall.
B. Level the bracket.
C. Verify with the customer where the conference table will be located, find the center of the conference
table, and then find the corresponding point on the mounting wall.
D. Measure the correct width between the drill holes of the mounting bracket.
Answer: C
Cisco dump 642-188 642-188 dumps 642-188 dumps
NO.2 What is the leveling process for the Cisco TelePresence System 1000 frame?
A. With only one display, there is no need to level the frame before attaching it to the wall
B. Attach the frame to the wall and level the frame by raising or lowering the feet.
C. Place a level on the middle and upper crossbars and adjust the feet as necessary to ensure that the
frame is horizontally level
D. Place a level on the side of the frame and adjust the feet as necessary to ensure that the frame is
vertically level
Answer: C
Cisco시험문제 642-188자격증 642-188 dumps 642-188
NO.3 Refer to the exhibit.
Identify the port number where the Audio Video expansion box should connect.
A. 4
B. 5
C. 6
D. 7
E. 9
F. 10
G. 11
H. 12
I. 13
Answer: H
Cisco기출문제 642-188자격증 642-188 dump 642-188 pdf
NO.4 Which statement is correct when tuning the cameras by using the WebGUI of the Cisco TelePresence
codec?
A. If there is a noticeable flicker on the screen, the 50 Hz Flicker Reduction button will eliminate the flicker
and increase the image resolution.
B. If the user is 4 to 5 feet (1.2 to 1.5 m) away from the display, click the 4 feet radio button for the Focus
Distance radio choice. If the user is farther than 5 feet (1.5 m) away, click the 6 feet choice.
C. If the room uses outside lighting, click the Disable radio button for the Camera Auto Brightness and
Camera Auto Color Balance choices.
D. Auto Color Balance can produce the best results when the colors of the walls in your room are white or
gray.
Answer: B
Cisco 642-188 dump 642-188자료
NO.5 When using Auto-Collaborate, what two actions need to be done to display the laptop content after
connecting the cable? (Choose two.)
A. Press the Auto-Collaborate softkey
B. Initiate Auto-Collaborate on the codec s GUI
C. Set the laptop resolution to 1024x768
D. Set your laptop resolution to 1024x720
E. Use function key on the laptop to send signal to external display
Answer: C,E
Cisco최신덤프 642-188 642-188 642-188덤프 642-188자료
NO.6 After connecting to a codec via WebGUI, you are prompted for a username and password. Which
username password combination is used on the codec by default?
A. Cisco, Cisco
B. admin, Cisco
C. Cisco, Cisco
D. admin, cisco
Answer: B
Cisco 642-188 642-188 dump 642-188 642-188
NO.7 Which statement is correct when discussing the microphone placement for the Cisco TelePresence
System 1000?
A. A microphone array is built into the frame of the Cisco TelePresence System 1000 so that a table
microphone is unnecessary.
B. Attach the microphone to the table by peeling the backing off the bottom of the microphone base and
stick the microphone to the alignment guide.
C. Place the microphone on the table approximately 18 inches (46 centimeters) forward of where the
participants will sit.
D. You can install the second microphone on the opposite side of the table to provide full-table
microphone coverage for audio-only conferences.
Answer: C
Cisco 642-188 642-188 642-188인증
NO.8 The customer decides to use static IP addressing for the codec. Which three parameters must be
configured? (Choose three.)
A. IP address
B. IP address subnet mask
C. gateway IP address
D. NTP server IP address
E. DNS server IP address
Answer: A,B,C
Cisco 642-188 642-188 642-188최신덤프 642-188최신덤프 642-188
NO.9 Which two statements are correct when calibrating the Cisco Telepresence cameras?
(Choose two) A. If the room uses fixed artificial lighting, click the Disable radio button fur the Camera Auto
Brightness and Camera Auto Color Balance
B. If the Auto Adjust test to automatically adjust lighting and color balance fails, you may need to add
more light
C. If the room uses fixed artificial lighting, click the Enable- radio button for the Camera Auto Brightness
and Camera Auto Color Balance
D. If the room uses outside lighting, click the Disable radio button for the Camera Auto Brightness and
Camera Auto Color Balance
Answer: A,B
Cisco 642-188자료 642-188 dumps
NO.10 During your assessment of a potential Cisco TelePresence System 1300 room, you notice:
The ceiling is 8 feel (2 4meters) high and currently illuminated with recessed parabolic light fixtures.
Which lighting recommendation is the most appropriate?
A. The Cisco Telepresence endpoint has a lighting facade which is designed to provide enough light for
the participants face and torso, so no lighting changes are required
B. The ceiling should be raised higher than 8 feet (2.4 meters) to accommodate appropriate light fixtures
for use with Telepresence
C. The existing fixtures are not ideal but are adequate for use with TelePresence
D. The existing fixtures should be replaced with recessed indirect light textures
E. No recommendation can be made until the lighting has been measured with a lux meter in the
appropriate zones
Answer: D
Cisco 642-188 642-188 642-188덤프
NO.11 What are the two choices for focal distance on a CTS-500? (Choose two)
A. 3.5 ft (1.06 m)
B. 4 ft (1.22 m)
C. 6 ft (1.83 m)
D. 8 ft (2.44 m)
E. 8.5 ft (2.59 m)
Answer: B,C
Cisco 642-188 642-188
NO.12 Which option on the Cisco Telepresence System administration WebGUI allows selecting table type?
A. Troubleshooting --> Hardware Setup > Display
B. Troubleshooting > Hardware Setup -> Configuration
C. Troubleshooting -> Hardware Setup --> Camera
D. Troubleshooting -> Hardware Setup -> Other Devices
Answer: B
Cisco 642-188 dumps 642-188인증 642-188
NO.13 When using HFR codec in a multipoint call, what happens when an endpoint without HFR calls in?
A. The entire call downgrades the data channel to 5 fps
B. The entire call downgrades the data channel to 5 fps but when the endpoint without HFR codec drops,
it automatically increases the data channel to 30 fps
C. The endpoint without the HFR shares data at 5 fps and all the other endpoints share at 3D fps
D. The call drops since there are different frame rates
Answer: A
Cisco 642-188 642-188 642-188자격증 642-188 dumps
NO.14 What is the default configuration for displaying presentations on a Cisco Telepresence System 1000?
A. An external display for displaying presentations is part of the default configuration.
B. Presentations are displayed as presentation-in-picture.
C. Presentations are displayed on an external display and include a presentation codec.
D. A projector and screen are used to display presentations.
Answer: B
Cisco 642-188 642-188 642-188 642-188시험문제
NO.15 During your RRA assessment of a potential Cisco TelePresence System 1300 room you notice:
The HVAC diffuser has noticeable noise (measured at48 1dB) which sounds like rushing air
What three recommendations should be made to the customer? (Choose three.)
A. The customer should turn the fan level down on the HVAC system to insure the fan noise is minimized
in the Cisco TelePresence room
B. The customer should contact an HVAC specialist to review and recommend an appropriate solution
C. The customer should not worry about the HVAC fan noise because the Cisco TelePresence System
uses a noise suppression algorithm designed to identify HVAC fan noise and minimize those frequencies
D. The customer should replace the diffusers with a diffuser that is rated with a noise criterion of 10 or
greater
E. The customer should replace the ducting directly above the room with acoustically treated ducting to
remove the sound of rushing airflow
Answer: B,D,E
Cisco인증 642-188기출문제 642-188 dumps 642-188 642-188자료
NO.16 In the Cisco TelePresence administration WebGUI, the camera Auto Adjust can be used to check which
setting?
A. life size
B. zoom and focus
C. white color balance
D. HDMI input threshold
Answer: C
Cisco 642-188 642-188 dump 642-188인증 642-188최신덤프
NO.17 Which is a design requirement for Cisco Telepresence room aesthetics?
A. Every room should be identical.
B. Maintain continuity in appearance among rooms
C. Carpet patterns and textures match from room to room
D. All rooms should be painted brown
E. The only wall treatment should be paint
Answer: B
Cisco기출문제 642-188 642-188자료 642-188기출문제 642-188 pdf
NO.18 Which three statements are correct when tuning the camera on a Cisco TelePresence CTS-1xxx system?
(Choose three.)
A. Target placement should match the green and red boxes on the screen, respectively
B. Place the large target three feet behind the small target.
C. Place the large target five feet behind the small target
D. Tune the camera so that the red and green bars line up as closely as possible
E. Perform auto-adjust to optimize focus and sharpness
Answer: A,C,D
Cisco 642-188 pdf 642-188인증
NO.19 Which two statements about the Cisco TelePresence codec software upgrade process are true?
(Choose two.)
A. Cisco TelePresence codecs must have IP address information for the TFTP servers that the Cisco
Unified Communications Manager uses.
B. During the codec upgrade process, all plasma displays must be in the off position.
C. Cisco TelePresence codecs use H-264 to download system software images and configuration files.
D. To abort the upgrade, you can reboot the codec manually before the codec finishes downloading the
software image.
E. The peripherals upgrade can take up to 60 minutes to complete. Do not manually reboot the codec
during the peripherals upgrade.
Answer: A,E
Cisco 642-188 pdf 642-188 dump
NO.20 Which statement is correct when discussing the Cisco TelePresence System 1300.?
A. The system is designed to support meetings of six to eight participants
B. The system features three 65-inch screens, three cameras, microphones, and speakers
C. Voice-enabled switching is performed by the codec to select the active speaker in the room and
capture the video for the remote side
D. The power and Ethernet outlets must be positioned directly behind the unit
Answer: C
Cisco 642-188덤프 642-188자격증 642-188
ITexamdump의 00M-624덤프의 VCE테스트프로그램과 642-996덤프는 한방에 시험을 패스하도록 도와드립니다. ITexamdump 에서는 최신버전의 000-N37시험에 대비한 고품질 덤프와 C_THR12_66시험 최신버전덤프를 제공해드립니다. 최고품질 P_HCMTM_64시험자료는 100% 간단하게 시험패스하도록 최선을 다하고 있습니다. IT인증시험패스는 이토록 간단합니다.
댓글 없음:
댓글 쓰기